M-Audio Lagoon Bedienerhandbuch

LAGOON™LAGOONMANUALTM

folder on your C: drive, install the Multimedia and ASIO drivers, plus install a groovymonophonic virtual analog synthesizer. This synth is the first

1. Connect the LAGOON PCI Toslink Optical Output to the Input of yourreceiving device.a) If you are sending a 2-channel signal, your recieving device

Using LAGOON with Application SoftwareOnce the Lagoon’s hardware, driver software, and Tools Applet are properlyinstalled, it is ready for use with yo

ASIO DRIVER INPUT DEVICES: When using the ASIO audio drivers withprograms that support ASIO-style audio, the input devices are displayed as monodevice

Info PageThe Info page provides information about the installed drivers. In the screen shotabove you can see that the driver version is 1.4 (you proba

ModeThe optical input and output can be configured separately either as S/PDIF or ADAT.This means mixing of both digital formats is possible as the LA

Sample RateIf Optical In or ADAT Sync In is selected as Clock source, then there is no need forchoosing a Sample rate. Only if LAGOON is selected you

Consumer ModeUsing the Consumer mode, you may change settings concerning the Copy bit, theGeneration status, the Category code, the Pre emphasis and t

The default setting for Encoded audio signal emphasis is Not indicated. It dependson your digital audio data if there is a need for encoding an emphas

Hint: S/PDIF signals are always related to audio channel number 1 and channelnumber 2. Therefore only device Lagoon In (1/2) and device Lagoon Out (1/

Table of ContentsIntroduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3Features . . . . . .

MIDI PageIn the MIDI page you can activate or deactivate the MIDI input and MIDI outputdevices separately by using the two Enable checkboxes. Remember

An error light that is turned on only indicates that this error happened in the past. Itdoes not mean that the error still exists. To check if the err

21Biphase code error(S/PDIF only)Parity error (S/PDIFonly)CRC error (S/PDIFmode only)1. The optical receiver has detected an invalid signal.2. The opt

22Alignment errorOut of syncOut of range Error Possible Reasons and Remarks Output ErrorThe output error is related to the optical output of the LAGOO

23Frame errorError Possible Reasons and Remarks OverflowDriver versionmismatchDSP errorLoss of realtime MIDI ErrorsMIDI errors are related to the MIDI

24Sample Rates and PerformanceInput sample rate always shows the detected sample rate coming in from youroptical cable. If this value varies continuou

TroubleshootingProblem AdviceOptical output doesnot work1. Check if you connected the cable correctly: Youshould see a red light coming out of the opt

Lifetime Limited WarrantyMIDIMAN warrants that this product is free of defects in materials and workmanship undernormal use so long as the product is

If you have any questions, comments or suggestions about this product orany M Audio or MIDIMAN product, we invite you to contact us directly at:MIDIMA

FCC Class B / European CE ComplianceWARNING: This equipment has been tested and found to comply with the limits fora CLASS B digital device, pursuant

IntroductionCongratulations on your purchase of a LAGOON PCI Digital Audio Card! With this card,high-quality digital audio processing becomes possibl

Minimum System Requirements• Windows 95 or 98• Pentium 166 or higher with MMX, 200 MHz recommended.• 32 MByte RAM, 64 MByte recommended.What’s in the

3. Toslink Optical Output: This standard female Toslink output jack accepts astandard male Toslink plug, typically connected to either an ADAT 8-chann

Hardware InstallationTo physically install the LAGOON card into your computer, please do the following:1. Turn off your computer.2. Remove the cover a

Windows Driver and Software InstallationThe Lagoon PCI includes a Windows 98/95 diskette containing the Windowsdrivers, ASIO drivers, and Lagoon Tools

Verifying Windows Driver InstallationWindows displays the Lagoon driver status in the Device Manager page of theSystem Properties dialog box. The Dev